Where Is The Carburetor On A Poulan Chainsaw? The Real Answer
So your Poulan Chainsaw is not running correctly, and you think your carburetor may need to be serviced or replaced. However, you’re unsure where the carburetor is located on the chainsaw and how to get to it.
The carburetor is located beneath the top shroud cover directly above where you grip the saw on the rear handle. To remove the carburetor, you’ll need first to unscrew and remove the cover. With the cover off, you will have access to the carburetor.
The socket size needed to remove the carburetor nuts is 8mm or 5/16 on most Poulan chainsaws. If your saw uses a different size, be sure to use the correct socket or wrench so as not to strip the screws.
Once you remove the carburetor, you can take it to a small engine mechanic or repair shop to have it serviced. Or, if you’re handy, you can attempt to clean or replace it yourself.
If you need help finding the right replacement carburetor for your Poulan Chainsaw, be sure to check out our Poulan Chainsaw Carburetor Finder guide.
How Do You Adjust The Carburetor On A Poulan Chainsaw?
To adjust the carburetor on your Poulan Chainsaw, you’ll need to locate the screws on the side of the carburetor. The screws are accessible thru holes on the side of the shroud cover.
There are usually three screws, one for low-speed, one for high-speed, and one for idle adjustment. To make adjustments, turn the screws with a flat-head screwdriver in the direction specified in your saw’s operator manual.
It’s important not to over-tighten the screws, as this can damage the carburetor.
If you are uncomfortable adjusting the carburetor on your own, you can take it to a small engine mechanic or repair shop.
Poulan Chainsaw Carburetor adjustment is an important part of saw maintenance. By keeping your carburetor adjusted, you can help extend the life and performance of your chainsaw.
Why Does My Poulan Chainsaw Die When I Give It Gas?
There are several reasons why your Poulan Chainsaw might die when you give it gas.
One reason could be that the carburetor is dirty or needs to be adjusted. As we mentioned before, the carburetor is located beneath the top shroud cover, and you’ll need to remove the cover to access it.
If the carburetor is dirty, you can try cleaning it with a carburetor cleaner. If this doesn’t work, you may need to replace the carburetor.
Another reason why your Poulan Chainsaw might die when you give it gas is that the spark plug might be fouled or faulty. The spark plug is located right beside the carburetor and can be removed usually with a 3/4 inch socket.
If the spark plug is fouled, you can try cleaning it with a wire brush. If this doesn’t work, you may need to replace the spark plug.
A dirty air filter will also alter how your chainsaw runs. The air filter is located beneath the shroud cover mounted over the carburetor’s air intake. To clean it, remove the shroud cover and pull the filter out.
You can tap the air filter on a hard surface to knock dirt and debris off it. You can also use compressed air to blow the filter clean.
Always blow the air filter from the inside out without too much pressure. If you use too much pressure, you can damage the air filter.
If the air filter is damaged or excessively dirty, you’ll need to replace it.
If the air filter is damaged, you’ll need to replace it.
Where Is The Carburetor Adjustment Screw?
The carburetor adjustment screw is located on the side of the carburetor. You will find the carburetor adjustment holes on the side of the chainsaw shroud. The adjustment holes will be marked (L) for low speed, (H) for high speed, and (T) for idle adjustments.
One screw is for low-speed adjustment, one is for high-speed adjustment, and one is for idle adjustment.
To adjust the carburetor, turn the screws with a flat-head screwdriver in the direction specified in your saw’s operator manual. It’s important not to over-tighten the screws, as this can damage the carburetor.
If you need help finding the right replacement carburetor for your Poulan Chainsaw, be sure to check out our Poulan Chainsaw Carburetor Finder guide.
Why Does My Poulan Chainsaw Only Run On Choke?
There are several reasons why your Poulan Chainsaw might only run on choke. One reason could be that the carburetor is dirty or needs to be adjusted. If adjustment or cleaning does not correct the issue, the carburetor might need to be replaced.
Another reason your Poulan Chainsaw might only run on choke is that the air filter might be dirty. The air filter is located beneath the shroud cover mounted over the carburetor’s air intake. To clean it, remove the shroud cover and pull the filter out.
You can tap the air filter on a hard surface to knock dirt and debris off it. You can also use compressed air to blow the filter clean. Always blow the air filter from the inside out without too much pressure. If you use too much pressure, you can damage the air filter.
If the air filter is damaged or excessively dirty, you’ll need to replace it.
Wrapping Up
We hope this guide has answered your question: “Where is the carburetor on a Poulan chainsaw?” As you can see, the carburetor is located beneath the top shroud cover and is easily accessible.
If the carburetor is dirty, you can try cleaning it with a carburetor cleaner. If this doesn’t work, you may need to replace the carburetor.
Remember, if you are having trouble finding the right replacement carburetor for your Poulan Chainsaw, check out our Poulan Chainsaw Carburetor Finder guide.
If you don’t feel comfortable working on your Poulan Chainsaw, we recommend taking it to a qualified technician for repair.
This concludes our guide on where the carburetor is located on a Poulan chainsaw. Thanks for reading!
Happy Sawing!
